-
Fokke van Saane answered a question 4 months, 1 week ago
The C100 has no dedicated timecode input. So, we users have to use a trick to ‘record’ timecode on the camera. What we do is we record an audio […]
-
Fokke van Saane answered a question 4 months, 2 weeks ago
I tried here too, with no success. I’ve tried the various settings that Tentacle Sync Studio Timecode reader has, no tsuccess.
I’ve also tried to […]
-
Fokke van Saane answered a question 4 months, 2 weeks ago
I might not understand the question fully, but i think you want this;
if you want to read timecode that is recorded on an audiotrack you have to use […]
-
Fokke van Saane answered a question 4 months, 2 weeks ago
No you are shorting the input and output on the lemo-side. Buy or make two cables or make a switch for in/out.
-
Fokke van Saane answered a question 5 months ago
Well, then use the good ol’ clap.. or Plural Eyes. Or both.
-
Fokke van Saane answered a question 5 months, 1 week ago
Looks like a defect to me. Please contact the mothership!
-
Fokke van Saane answered a question 5 months, 1 week ago
and the 3.5mm plug is connected?
-
Fokke van Saane answered a question 5 months, 1 week ago
I still haven’t got an sync-E but i know it does send timecode over bluetooth, but only to his own application, not as timecode signal into another […]
-
Fokke van Saane answered a question 5 months, 1 week ago
Genlock? There is no Genlock on the Tentacle. Only timecode.
The 688 should keep timecode for a few hours when turned off.
If the RED is turned off […]
-
Fokke van Saane answered a question 5 months, 1 week ago
Are you sure that the Red is constantly looking at the timecode, or does it jam once and then runs on it’s own clock? My suspicion is that the […]
-
Fokke van Saane answered a question 5 months, 1 week ago
Tentacle Sync Studio can look at timecode anywhere in the file. My default setting is in the middle. But it looks like AvidMC is looking at the […]
-
Fokke van Saane answered a question 5 months, 2 weeks ago
There are previous versions available on the website.
I don’t think it will solve it but you can give it a try.
Does any of the settings help you […] -
Fokke van Saane answered a question 5 months, 2 weeks ago
Careful in the sense that you overload it, yes. But i don’t think you break the circuit in there with line level output from the Tentacle.
-
Fokke van Saane answered a question 5 months, 2 weeks ago
That’s why i enable Auto Output Level. Then it is always on LINE unless it senses a DC from a DSLR mic input.
-
Fokke van Saane answered a question 5 months, 3 weeks ago
Is there an arrow on the demo cable showing the direction of the signal flow?
-
Fokke van Saane answered a question 5 months, 3 weeks ago
Do you use the correct Lemo cable? They come in two variants; an input and an output cable.
-
Fokke van Saane answered a question 6 months ago
Not by the user. If the battery is broken then it needs to go to Tentacle Sync.
-
Fokke van Saane answered a question 6 months ago
There are separate input and output cables because Lemo uses different pins for input and output. Looks like you use the wrong cable.
-
Fokke van Saane answered a question 6 months, 1 week ago
If the manual is not clear enough, please re-read it and ask this forum what you don’t understand.
You basically say; “i don’t understand anything […]
-
Fokke van Saane answered a question 6 months, 1 week ago
Yeah, what i thought
- Load More
offline active 2 days, 22 hours ago